Bently Nevada Proximitor Wiring Diagram

Bently nevada proximitor wiring diagram. This manual does not contain all the information required to operate and maintain the proximitor/seismic monitor. When this is not possible or practical, it will be necessary to determine these values yourself 1701/22 fieldmonitor management interface module (fmim) Linear range 2 mm (80 mils).

305 metres (1,000 feet) maximum length between 3300 proximity transducer and monitor. The following ways of contacting bently nevada are provided for those times when you cannot contact your local representative: Mailing address 1631 bently parkway south minden, nevada usa 89423 usa telephone 1.775.782.3611 1.800.227.5514 fax 1.775.215.2873 Document number description 130432 3500 system field wiring diagrams 141706 3500 galvanic isolator interface 129766 3500 monitoring system rack weatherproof housing 136275 3500/08 diagnostics access panel 129767 3500/15 ac and dc power supplies

Consult performance specification 155687 for signal rolloff at high frequencies when using longer field wiring lengths or external safety barriers located some distance from the monitoring system. (refer to documents an013 and an015.) no barriers or 3300 internal barriers transducer power common (ground) input signal monitor terminal strip cable shield proximitor sensor probe transducer power common (ground). Bently nevada, keyphasor and proximitor contact information the following ways of contacting bently nevada are provided for those times when you cannot contact your local representative: Internal proximitor sensor or transducer i/o modules.

Bently nevada* asset condition monitoring 3500/42m proximitor */seismic monitor. Linear range begins at approximately 0.25 mm Proximity transducer system provides an output voltage directly proportional to the distance between the probe tip and the observed conductive surface. When using cable from another supplier, consult their datasheet or contact the manufacturer to obtain capacitive values.

You can search for a document using its number or description. Recommend using 3 conductor shielded triad cable and tinned field wiring. Channels 1 and 2 ca. Field wiring 0.2 to 1.5 mm2 (16 to 24 awg).

Ranges 01 and 11 only.) 0 5 3300xl nsv and 3300 ram proximitor sensor, 200 mv/mil (ranges 01 and 11 only). On the bently nevada dvd. The proximitor will follow any motion from 0 to 4000 cps, constant or variable. The ge / bently nevada 3300 xl 8mm proximity transducer system consists of one 3300 xl 8mm probe, one 3300 xl extension cable, and one 3300 xl proximitor sensor.

The three parts of a proximity transducer system are: Use the following wiring diagrams to connect the field wiring between the proximitor sensor and the monitoring instruments. >the link below shows the wiring diagram for a monitran 1185, >taken from a spec sheet on the web: Capacitance values for the field wiring provided by ge for use with bently nevada transducers are shown in table 1.

Network adapter (specific to the network communication type) 7. The system accuracy and interchangeability specifications do not apply The system provides an output voltage that is directly proportional to the distance between the probe tip and the observed conductive surface and can measure both static (position) and. One for each monitor 3.

The voltage output varies directly as the distance between the probe and the observed surface varies. Maximum length of 305 meters (1,000 feet) between the 3300 xl proximitor sensor and the monitor. Transducer wiring diagrams are available in the 1900/65a field wiring diagram document (173089). Proximitor / seismic monitor bently nevada 3500 software configuration of proximitor module bently nevada 3500.

Hold alarm set points (alert & danger) compare monitored values with. Keyphasor signal input (either an internal proximitor sensor or transducer i/o module) 5. The ruggedised coaxial cable used in the system has a center conductor two screens.